[Résolu] Accès internet amiga 2000 (Roadshow)

15 sujets de 1 à 15 (sur un total de 19)

  • 1
  • 2
  • verik

      #207632

      Bonjour

      Je n’arrive pas à aller sur internet avec mon amiga.

      J’ai un a2000, avec carte réseau a2065 et roadshow

      Je précise que tout est sans doute bien installé aussi bien logiciel que matériel, car l’internet marchait avant chez le précédent propriétaire.

      La je suis avec free pour l’accès internet, j’ai mis mon ip, gateway, masque dans les divers fichiers de roashow.

      Quand je lance ibrowse il me dit: échec de la recherche de l’hote, pas d’entrée DNS trouvée

      J’avoue ne pas savoir ou mettre les dns dans roadshow.

      NdBigdan : ajouté [Résolu]

      sayasupacrew

        #207716

        je t’avoue que je connais peu road show, et que sur la configuration des piles tcp/ip, nean moins cela m’intérrèsse, vue que suis sur la mêmes machine.

        https://www.youtube.com/@sayasupa

        Admin

        bigdan

          #207731

          Verik : ta freebox est paramétrée en mode routeur ou bridge ?

          Au pire tu peux renseigner les DNS Free en dur avec 212.27.40.240 et 212.27.40.241

          Ou encore utiliser ceux de Google (4.4.4.4 par exemple) ou OpenDNS

          Je peux te guider dans Miami/MiamiDX ou Genesis par exemple mais je n’ai pas Roadshow donc ce sera plus compliqué même si c’est toujours AmiTCP amélioré et recarossé 😉

          verik

            #207737

            Je voudrais essayé dans un premier temps de réaliser ma connexion sous roashow.

            voici le liens le plus intéressant que j’ai trouvé (il faut le traduire dans le navigateur)

            http://www.ppa.pl/programy/roadshow-konfiguracja-stosu-tcp-ip-pod-katem-dostepu-do-internetu-przez-modem-dsl-router-siec-lokalna-dla-systemow-amigaos.html

            Mais j’avoue que les dns c’est un mystère pour moi. Ou les placer dans les fichiers de réglage? j’ai bien fait quelques essai mais sans succès. Le plus simple, je vais faire des photos des pages textes des fichiers (car il n’y a pas de réglage avec des graphismes) et comme cela vous pourrez surement mieux comprendre…

            Admin

            bigdan

              #207756

              Verik : logiquement tu indique l’adresse de ta freebox (192.168.0.254 ou 192.168.1.1 généralement pour une box) en tant que passerelle et dns.

              Tu as d’autres machines connectées sur ta box ?

              Fait un copier-coller de tes fichiers de configs Roadshow et on essaiera de te guider 😉

              verik

                #207830

                ça va être un peu long  lire mais je commence:

                voici le fichier config de ma carte reseau a2065

                # $VER: A2065 1.2 (27.11.2010)
                #
                # Configuration for the Commodore/Ameristar “A2065” Ethernet card.

                # The device name is mandatory
                device=a2065.device

                # If not provided, unit number 0 will be used. You may
                # have to change this if there are multiple cards of the
                # same type installed in your machine, or if your network
                # hardware supports several independent connections
                #unit=0

                # You must either pick a fixed (static) IPv4 address and
                # a corresponding subnet mask, or request DHCP (dynamic)
                # network address configuration.
                # You can combine address/netmask/dhcp, which has the effect
                # of asking the DHCP server to assign the requested IPv4
                # address and subnet mask to this interface, if possible.
                address=192.168.0.65
                netmask=255.255.255.0
                configure=dhcp

                # If no DHCP server is present in your network, you can
                # use automatic interface IPv4 address assignment through
                # the ZeroConf protocol. Note that this will not set up
                # default route and DNS servers for you, only the interface
                # address is configured.
                #configure=auto

                # This variant of automatic IPv4 address assignment should
                # be used in a wireless network instead of ‘configure=auto’
                #configure=fastauto

                # You can enable diagnostic messages which can be helpful in
                # tracking down configuration errors.
                #debug=yes

                # You can choose how much memory will be used when handling
                # incoming and outgoing network traffic for this device.
                # The default is to reserve 32 buffers of 1500 byte each, both
                # inbound and outbound traffic. Larger values may provide
                # better performance.
                iprequests=64
                writerequests=64

                # For diagnostic and monitoring purposes it can be helpful to
                # capture network traffic that flows through this interface.
                # To enable this option, select one of filter=local,
                # filter=ipandarp or filter=everything
                #filter=local
                #filter=ipandarp
                #filter=everything

                # This option disables a workaround required for the Ariadne
                # network hardware, which, if enabled, would otherwise cause
                # the interface setup procedure to take longer than really
                # necessary.
                requiresinitdelay=no

                verik

                  #207831

                  fichier roadshow:

                  # $VER: name_resolution 1.1 (24.10.2010)
                  #
                  # This file is used by the name resolution process which associates
                  # raw IP addresses with domain names and the other way round. You
                  # can configure the addresses of the domain name system servers to
                  # use and how the lookup process will translate host names you provide
                  # before they are looked up.

                  # You can specify the IP addresses of up to three domain name system
                  # servers which will be queried in the order you provide here. Each
                  # line must start with “nameserver” and then must be followed by
                  # an IP address.
                  nameserver 212.27.40.240
                  nameserver 212.27.40.241
                  #nameserver 192.168.0.3

                  # If a host name is to be looked up which has no trailing domain
                  # name attached, a default domain name can be appended to it
                  # prior to lookup
                  #domain name.com

                  # You can configure the list of host names for lookup. The search list
                  # is normally determined from the local domain name; by default, it
                  # begins with the local domain name, then successive parent domains that
                  # have at least two components in their names will be searched. This may
                  # be changed by listing the desired domain search path following the ‘search’
                  # keyword with spaces or tabs separating the names. Up to six domain
                  # names may be listed.
                  #search my.first.domain my.second.domain

                  # The ‘sortlist’ parameter allows addresses returned by the name
                  # resolution process to be sorted. A sortlist is specified by IP address
                  # netmask pairs. The netmask is optional and defaults to the natural
                  # netmask of the net. The IP address and optional network pairs are separated
                  # by slashes. Up to 10 pairs may be specified.
                  #sortlist 212.27.40.240/255.255.255.0 212.27.40.241

                  verik

                    #207833

                    fichier routes

                    # $VER: routes 1.1 (24.10.2010)
                    #
                    # Routes which should be established when the protocol stack
                    # initializes itself. Each line corresponds to a route which should
                    # be established, very much like the parameters passed to the
                    # AddNetRoute command. The template is:
                    #
                    #  DST=DESTINATION/K,HOSTDST=HOSTDESTINATION/K,NETDST=NETDESTINATION/K,
                    #  VIA=GATEWAY/K,DEFAULT=DEFAULTGATEWAY/K
                    #
                    # You must either specify the default route, or specify a route with a
                    # destination address. Note that no duplicates are allowed, i.e. there
                    # can be only a single default route and the same route may not be
                    # established twice.
                    default 192.168.0.1

                    verik

                      #207834

                      fichier host:

                      # $VER: hosts 1.1 (24.10.2010)
                      #
                      # Host Database
                      # This file should contain the addresses and aliases
                      # for local hosts that share this file.
                      # It is typically used only for “AddNetInterface” and other
                      # operations before the name resolution server is started.
                      #
                      #
                      #127.1      localhost localhost.my.domain
                      127.0.0.1        localhost
                      192.168.0.60     Amiga     Amiga
                      192.168.0.65     A2000     A2000
                      192.168.0.100    MSNB      MSNB
                      #
                      # Imaginary network.
                      #0.2     myname.my.domain myname
                      #0.3     myfriend.my.domain myfriend

                      Merci pour la suite…

                      Tryphon

                        #207857

                        Je pense qu’il te manque le paramétrage du fichier a2065 dans Devs:NetInterfaces

                        address=192.168.0.nnn     (nnn selon ton IP locale)

                        netmask=255.255.255.0

                        Mettre en commentaire la ligne

                        #configure=dhcp

                        en effet, en mode dhcp, Samba risque de ne pas fonctionner. L’adresse IP fixe de ton Amiga a aussi besoin d’être paramétrée dans la configuration de Samba.

                        Le manuel PDF “Installation.pdf” de l’archive Roadshow explique tout ceci en détail.

                        Admin

                        bigdan

                          #207862

                          Verik : ta freebox a quelle adresse IP exactement ?

                          Commence par changer la config de la passerelle par défaut avec la ligne default 192.168.0.1 dans le fichier de config route avec 192.168.0.254 ou 192.168.1.1 (enfin bref avec l’IP de ta freebox).

                          Si cela ne fonctionne pas, rajoute nameserver Adresse.IPde.Ta.Freebox dans Roadshow.

                          Tryphon : le dhcp peut fonctionner aussi (IP dynamique) si activée dans la freebox (en mode routeur).

                          Mais sinon tu as raison, il doit tester en IP statique pour vérifier si cela fonctionne 😉

                          Je reprécise que je n’ai pas Roadshow et un classic sous la main pour tester (je ne suis pas chez moi).

                          verik

                            #207955

                            Rien ne marche.

                            Je pense que il n’y a aucun contact vers l’internet.

                            Par exemple si je fait AddNettInterface a2065 dans le shell normalement il devrait me sortir les caractéristiques de la carte réseau et ça me dit :

                            could not add interface “a2065” (objet exist)

                            Si je lance tango dans samba il me met plein de point exclamation devant

                            no: ismbhandler

                            no samba:bindie

                            ! recherche des periphéries montés

                            recherche de l’hote !

                            recherche d’une liste maitre !!!

                            J’ai changer de câble réseau et ma carte a bien deux diodes verte qui confirme mon branchement réseau.

                            Mon problème sort peut être de roadshow

                            Dans tout les cas il me dit dans ibrowse pas d’entrée dns trouvée

                             

                            Tryphon

                              #207956

                              Bigdan : je confirme, le dhcp fonctionne sous roadshow et c’est parfait pour la navigation. Mais je crois que Samba ne récupère pas automatiquement l’IP ce qui complique l’échange de fichiers.

                              Dans le fichier name_resolution as-tu essayé avec :

                              nameserver 192.168.0.1         (seul)

                              Ne tente pas d’utiliser Samba (ou Tango) avant d’avoir obtenu une connexion fonctionnelle. Sous le shell, exécute ping 192.168.0.1 (est-ce bien l’adresse de ta passerelle?)

                              Que dit la commande shownetstatus ?

                              Vérifie que l’adresse IP de ton 2000 (192.168.0.65?) n’est pas déjà utilisée par une autre machine (source de conflit).

                              Si le ficher a2065 (peux-tu le publier?) est déjà présent dans Devs:NetInterfaces, inutile d’envoyer la commande AddNetInterface.

                              Je ne connais pas la freebox mais parfois dans un routeur on peut limiter les plages d’adresses IP utilisables, certaines peuvent être bannies … à vérifier.

                              verik

                                #208003

                                dans le shell ping 192.168.0.1 (c’est bien l’ip de ma passerelle) cela fait

                                ping: wrote 192.168.0.1  64 chars. ret=1

                                cela se répète sans cesse

                                shownetstatus:

                                local host adress  = 192.168.0.14 (on interface “a2065″)  comme il a choisi ca j’ai mis cette ip pour l’amiga

                                default gateway adress    = 192.168.0.1

                                domain name system servers = 212.27.40.240.  212.27.40.241

                                <span class=”normal” style=”font-size: small;”></span>

                                fichier a2065 dans devs/ netinterfaces

                                <span class=”normal” style=”font-size: small;”></span>

                                # $VER: A2065 1.2 (27.11.2010)
                                #
                                # Configuration for the Commodore/Ameristar « A2065? Ethernet card.

                                <span class=”normal” style=”font-size: small;”></span>

                                # The device name is mandatory
                                device=a2065.device

                                <span class=”normal” style=”font-size: small;”></span>

                                # If not provided, unit number 0 will be used. You may
                                # have to change this if there are multiple cards of the
                                # same type installed in your machine, or if your network
                                # hardware supports several independent connections
                                #unit=0

                                <span class=”normal” style=”font-size: small;”></span>

                                # You must either pick a fixed (static) IPv4 address and
                                # a corresponding subnet mask, or request DHCP (dynamic)
                                # network address configuration.
                                # You can combine address/netmask/dhcp, which has the effect
                                # of asking the DHCP server to assign the requested IPv4
                                # address and subnet mask to this interface, if possible.
                                address=192.168.0.14
                                netmask=255.255.255.0
                                <span class=”normal” style=”font-size: small;”>#</span>configure=dhcp

                                <span class=”normal” style=”font-size: small;”></span>

                                # If no DHCP server is present in your network, you can
                                # use automatic interface IPv4 address assignment through
                                # the ZeroConf protocol. Note that this will not set up
                                # default route and DNS servers for you, only the interface
                                # address is configured.
                                #configure=auto

                                <span class=”normal” style=”font-size: small;”></span>

                                # This variant of automatic IPv4 address assignment should
                                # be used in a wireless network instead of ‘configure=auto’
                                #configure=fastauto

                                <span class=”normal” style=”font-size: small;”></span>

                                # You can enable diagnostic messages which can be helpful in
                                # tracking down configuration errors.
                                #debug=yes

                                <span class=”normal” style=”font-size: small;”></span>

                                # You can choose how much memory will be used when handling
                                # incoming and outgoing network traffic for this device.
                                # The default is to reserve 32 buffers of 1500 byte each, both
                                # inbound and outbound traffic. Larger values may provide
                                # better performance.
                                iprequests=64
                                writerequests=64

                                <span class=”normal” style=”font-size: small;”></span>

                                # For diagnostic and monitoring purposes it can be helpful to
                                # capture network traffic that flows through this interface.
                                # To enable this option, select one of filter=local,
                                # filter=ipandarp or filter=everything
                                #filter=local
                                #filter=ipandarp
                                #filter=everything

                                <span class=”normal” style=”font-size: small;”></span>

                                # This option disables a workaround required for the Ariadne
                                # network hardware, which, if enabled, would otherwise cause
                                # the interface setup procedure to take longer than really
                                # necessary.
                                requiresinitdelay=no

                                <span class=”normal” style=”font-size: small;”></span>

                                 

                                Anonyme

                                  #208004

                                  Le 30/03/2014 :

                                  Bonjour
                                  Je n’arrive pas à aller sur internet avec mon amiga.

                                  Si Jay Miner nous voit, de la haut, cette phrase doit lui faire super plaisir 🙂

                                15 sujets de 1 à 15 (sur un total de 19)

                                • 1
                                • 2
                                • Vous devez être connecté pour répondre à ce sujet.

                                Forums AmigaOS, MorphOS et AROS Général [Résolu] Accès internet amiga 2000 (Roadshow)

                                Amiga Impact